Posted on

Learn Woodworking With These Simple Tips And Advice

It is certainly tough to operate a profitable woodworking enterprise. To be successful at woodworking, you need to be dedicated and put in hard work. The following article offers many great tips on how to get started in woodworking. Continue reading through each tip carefully and use them to your advantage.

Woodworking can be a fun, and satisfying, hobby. However, it is very important to play it safe when working with tools, substances that cause fumes and other common dangers of the craft. Be sure to wear safety glasses, allow plenty of fresh air for ventilation when using oil-based products and always read the directions before you start anything!

Always be on the lookout for good woodworking tips. If you meet professionals, ask them for their best tips. If you find a magazine chock full with tips, pick it up so that you can keep it in your archive. Even record TV shows that have woodworking in them to glean any tips you my find there.

If you are working with wood, it can be very dangerous to have a messy workshop. Do everything you can to keep your work area clean and well-maintained. Every time you are done with a specific tool, out it away before you get another. It may seem like this is time consuming, but you won’t have any reason to clean up later.

Become more accurate by using a drafting square. If you need an accurate square that’s about 2″ to 3″, you have limited options. Drywall squares tend to be very inaccurate. With carpenter squares, you have to hook them onto your work piece’s edge. A drafting square can be easily used if you happen to have one lying around. If you don’t, they are pretty cheap to find at art stores. They are incredibly accurate and as useful as a tape measure.

Always clean up sanding dust thoroughly before staining or applying a topcoat. If you want a smooth finish, dust is your enemy. Use a vacuum over blowing dust into the air because it settles back onto the wood, and use a damp cloth to ensure all dust is removed from the wood in your final cleanup prior to staining or applying a top coat.

You need a good stair gauge in your shop. They not only assist with stair jack layouts, but can also be used when your carpenter’s square needs to be clamped. This can make your carpenter’s square into a guide for your circular saw. This square will make sure your cuts are straight each time.

Learn about using pilot holes. This is pretty simple to do. When driving a screw or hammering a nail into a little piece of wood or getting pretty close to the edge of a piece, it tends to split. Sometimes it’s unavoidable to put a fixing into a place like this. However, drilling a hole through the joint that’s a bit smaller than the fixing can prevent it from splitting.

If you are going to be doing a big woodworking project on the outside of your home, check to make sure it is within the rules. Your local government may have zoning regulations or even a permit process needed for structures like garages, decks and even storage sheds. Also check with your neighborhood association if there is one.

Wear the right shoes while working on wood. This is necessary since your work area may be full of wood chips, nails and all types of tools. Your feet deserve protection from the inevitable stepping on a nail as well as you accidentally kicking or dropping something heavy. Your shoes need to be great for walking around as you work.

When using a table saw, use a block of wood clamped to the fence to set your length. Using the fence directly could result in a board being kicked back at you. To make measurements easy, use a block that is exactly 1 inch in length. Then all you have to do is set the fence length 1 inch greater than your desired length.

Enjoying woodworking with a couple beers may sound fun. However, working with a saw and drinking is a terrible combination. Don’t work on anything if you are drinking. Also, never take any major drugs prior, whether they are prescription or illegal.

When staining a completed woodworking project stir your stain often, especially if you are using a liquid stain. As stain sits, the sealer separates from the stain and settles to the bottom. If you do not stir the stain often, your piece may have different shades of stain because of this separation.

Do you know that different colored tin snips make different kinds of cuts? Tin snips with red handles are used for making left hand turns. Green handled tin snips are used for making right hand turns. Finally, yellow handled tin snips are used for straight lines and gradual curves.

Be careful if you are gluing and staining at the same time. If you apply too much glue to a visible section of the piece you are working with, it can fail to soak into the wood before it dries. Once it is dry, it can cause your stain not to stick properly to the grain.

Consider a woodworking class at your local community college. The skills and experience you pick up can go a long way towards getting started. Even if you already are a woodworker, you’ll meet others who have an interest in the field. These are future friends or possibly even potential professional relationships waiting for you to explore.

Use only one extension cord for your power tools to avoid having an octopus of cords. Take the time to unplug the tool you are not using and plug in the tool you wish to use. Reduce the risk of tripping over cords or the possibility of a nasty shock with this basic safety procedure.

Make sure you know all the steps you’ll have to complete to finish your project. You could make mistakes by only reading the instructions once. Go over the instructions carefully and do a few tests if you need to.

Woodworking is extremely interesting. Putting all of the things learned here to good use can be fun and rewarding to most people. Apply what you’ve just learned, and create something great to share with those around you. You can surprise yourself with the lovely projects created with woodworking. Good luck.